black porcelain pendant light

Soon after being established in 2009, zangra started to successfully cooperate with different porcelain factories all over the world – a cooperation that continues to this day. In recent years, zangra has spent a lot of time in world’s most famous porcelain cities. From Limoges in France to Jingdezhen in China, zangra was able to work at legendary porcelain factories. So in cooperation with the staff zangra created new models and rediscovered old forgotten molds. A number of old molds were put back in production making new pieces. zangra’s porcelain is still produced by hand, piece by piece. This makes each piece unique. zangra's work proved successful with their products being sold all over the world.

Our glass globes and shades are the perfect match for zangra's porcelain, bakelite and brass lamp collections. The shades are available as spare parts, allowing you to extend the life of your lamp if a globe needs replacement.
Any bubbles or parting lines on our products are proof of the real craftsmanship that goes into the manufacturing process.

Browse our extensive collection here:
* globes/shades size S: Ø74.5mm screw thread
* globes/shades size M: Ø84.5mm screw thread
* globes/shades size L: Ø100mm neck
* globes/shades size XL: Ø120mm neck

The light bulb is not included when you buy this light. You will find here the whole selection of LED, incandescent, stick and halogen light bulbs. Take into account that each light needs a specific type of light bulb. You will find the kind of light bulb that it requires under the "Technical Description" tab.

E27 stands for the type of the fitting of a lamp. E27 stands for a 27 mm diameter thread. "E" stands for Edison thread. So you always have to put an E27 light bulb in a fixture with an E27 fitting. E27 is the standard in England and most European countries.
The early light bulbs (remember them?) had a similar screw thread.
Be careful though, because there are also countries where E26 bulbs are the norm (for example in the United States).
If you would like to know which standard applies in your country, check out this page.
Check out here the complete collection of E27 light bulbs by zangra.

1. Above a dining table
Above a dining table, lower the pendant lamp so that it is up to 60 to 70 cm above the table. This means you won’t be blinded when you eat and won’t hit your head when you get up. The height indicated corresponds to the distance between the top of the table and the lowest part of the suspension light. The light should end up approximately at your eye level when you are standing, and you’ll see the underside of the light when you are sitting. You need to ensure that the light diffused by the pendant lamp illuminates the entire table.
2. Above a coffee table
A pendant lamp placed above a coffee table should be placed higher than those installed above a dining table so that you do not hit your head.
3. In the middle of a room
You should leave about 210 cm between the floor and the lowest part of the pendant lamp so that tall people do not hit their heads. If it is hung above a piece of furniture or in a corner, it can go down lower.
4. Above the kitchen worktop
Hand the light at least 180 cm from the floor or between 75 and 85 cm from your worktop or countertop. Don't hang your suspension too high, so you don't have to look at the light all the time, but it shouldn’t be too low either as it might not illuminate the whole worktop.
5. On each side of a mirror in the bathroom
If you want to hang two pendant lamps on each side of a mirror, they are best positioned according to the average eye height of your family members. It is also recommended that the two suspension lights are not more than 70 cm apart so that the face is sufficiently illuminated.

No screws are supplied, as the type of screw depends on the material of the wall or ceiling (concrete, brick, plasterboard, wood).
You need a different type of screws depending on each material.

Do not use electrical screwdrivers when installing ceramic or porcelain items. We recommend to first drill a hole in the wall, fit the right plugs inside and use a manual screwdriver to fix the screws in place. Be especially careful during the final tightening of the screws.