black pendant light - Ø 10 cm

Our glass globes and shades are the perfect match for zangra's porcelain, bakelite and brass lamp collections. The shades are available as spare parts, allowing you to extend the life of your lamp if a globe needs replacement.
Any bubbles or parting lines on our products are proof of the real craftsmanship that goes into the manufacturing process.

Browse our extensive collection here:
* globes/shades size S: Ø74.5mm screw thread
* globes/shades size M: Ø84.5mm screw thread
* globes/shades size L: Ø100mm neck
* globes/shades size XL: Ø120mm neck

The light bulb is not included when you buy this light. You will find here the whole selection of LED, incandescent, stick and halogen light bulbs. Take into account that each light needs a specific type of light bulb. You will find the kind of light bulb that it requires under the "Technical Description" tab.

E27 stands for the type of the fitting of a lamp. E27 stands for a 27 mm diameter thread. "E" stands for Edison thread. So you always have to put an E27 light bulb in a fixture with an E27 fitting. E27 is the standard in England and most European countries.
The early light bulbs (remember them?) had a similar screw thread.
Be careful though, because there are also countries where E26 bulbs are the norm (for example in the United States).
If you would like to know which standard applies in your country, check out this page.
Check out here the complete collection of E27 light bulbs by zangra.

All light fittings are classified according to their IP value. These IP values (International Protection or Ingress Protection) indicate the degree of protection of the light fitting against dust and moisture. The IP value consists of two digits: the first digit indicates the level of protection against dust; the second, the level of protection against moisture. The higher the IP value, the higher the protection. Check this diagram to see the different existing IP values.
 

What does the IP20 value mean on this light fitting?

IP20 means that the light fitting:
2: is protected against the intrusion of solid particles with a dimension greater than 12.5 millimetres.
0: has no protection against water penetration.

This light fitting can be installed indoors, but not in wet areas.
It is not recommended to install this light fitting outdoors.

A device with an IP20 value is not protected against dust or moisture. A light fitting marked IP20 may have holes to prevent overheating. However, the lamp is protected against contact with objects larger than 12.5 mm, such as a hand or finger.
This model is suitable for indoor use, but not outdoors.

1. Above a dining table
Above a dining table, lower the pendant lamp so that it is up to 60 to 70 cm above the table. This means you won’t be blinded when you eat and won’t hit your head when you get up. The height indicated corresponds to the distance between the top of the table and the lowest part of the suspension light. The light should end up approximately at your eye level when you are standing, and you’ll see the underside of the light when you are sitting. You need to ensure that the light diffused by the pendant lamp illuminates the entire table.
2. Above a coffee table
A pendant lamp placed above a coffee table should be placed higher than those installed above a dining table so that you do not hit your head.
3. In the middle of a room
You should leave about 210 cm between the floor and the lowest part of the pendant lamp so that tall people do not hit their heads. If it is hung above a piece of furniture or in a corner, it can go down lower.
4. Above the kitchen worktop
Hand the light at least 180 cm from the floor or between 75 and 85 cm from your worktop or countertop. Don't hang your suspension too high, so you don't have to look at the light all the time, but it shouldn’t be too low either as it might not illuminate the whole worktop.
5. On each side of a mirror in the bathroom
If you want to hang two pendant lamps on each side of a mirror, they are best positioned according to the average eye height of your family members. It is also recommended that the two suspension lights are not more than 70 cm apart so that the face is sufficiently illuminated.

This lamp is fixed to the ceiling/wall with a metal bracket. The screws that serve to attach the bracket to the lamp are included. The screws used to attach the bracket to the ceiling/wall are not included because the type of screw depends on the material of the wall or ceiling (concrete, brick, plasterboard, wood).